How to Fix the XBox 360 CD-ROM

The Xbox 360 has a DVD drive for playing optical game discs. Vibrations from the CD-ROM/DVD drive's motor can dislodge a magnet from inside of the case and cause game discs to play erratically. You can fix the game console's CD-ROM/DVD drive so that optical game discs will again play correctly. You need a few hardware tools to partially disassemble the Xbox 360, but you do not need to have electrical skills.



•Step 1
Place a bath towel on a table. Remove all cables from the Xbox 360. Place the Xbox 360 horizontally on the bath towel with the power button facing you. Squeeze the upper left corner of the Xbox 360 with one hand while pulling up on the open slot at the bottom right corner with the other hand. Slide the faceplate off the Xbox 360 once it has been loosened by the squeezing and pulling.

•Step 2
Insert the tip of the #10 Torx screwdriver into the top hole in the ventilation grill on the right side nearest to you. Lift up on the tip of the #10 Torx screwdriver to release the plastic latch inside. Repeat this procedure in the middle hole at the top and the top right hole farthest from you. Repeat this procedure with the ventilation grill on the left side of the Xbox 360.

•Step 3
Turn the Xbox 360 over. Lift up on the bottom shelf to reveal the 14 screws. Remove the screws with the #20 Torx screwdriver. Turn the Xbox 360 over.

•Step 4
Lift the outer casing off the Xbox 360. Unscrew the back panel using the #10 Torx screwdriver. Remove the plastic inserts on the left and right side of the Xbox 360. Remove the back panel.

•Step 5
Remove the screws from around the metal plate on the Xbox 360 with the #10 Torx screwdriver. Lift the metal plate off the Xbox 360.

•Step 6
Remove the screws from around the CD-ROM/DVD drive with the Phillips jeweler's screwdriver. The CD-ROM/DVD drive is the metal rectangular box lying next to the hard drive.

•Step 7
Lift the CD-ROM/DVD drive up. Pull the two connectors out of the back of the CD-ROM/DVD drive with your fingers.

Fixing The Xbox 360 DVD/CD-ROM Drive

•Step 1
Place the CD-ROM/DVD drive on the bath towel with the warning sticker facing down. Pull the disc tray halfway out of the front of the CD-ROM/DVD drive with your fingers.

•Step 2
Remove the screws from around the CD-ROM/DVD drive with the Phillips jeweler's screwdriver. Remove the case from off of the CD-ROM/DVD drive. Grab hold of the magnet that is now clinging to the inside of the case.

•Step 3
Apply bonding glue to one side of the magnet. Place the magnet, bonding glue side down, onto the center of the spindle hole at the middle of the CD-ROM/DVD drive. Push down on the magnet for 10 seconds. Let the bonding glue set for an hour.

•Step 4
Place the case back onto the CD-ROM/DVD drive. Reattach the screws. Push the disc tray back into. Turn the CD-ROM/DVD drive over.

•Step 5
Reattach the two connections to the back of the CD-ROM/DVD drive. Place the CD-ROM/DVD drive back into its original position on the Xbox 360. Reattach the screws.

•Step 6
Place the metal plate back onto the Xbox 360. Reattach the screws. Reverse the disassembly process to reassemble the Xbox 360. Reattach the cables.



Read more: How to Fix the XBox 360 CD-ROM eHow.com http://www.ehow.com/how_6806971_fix-xbox-360-cd_rom.html#ixzz0vaPN0ddV

How to Fix Virus Damage

Despite your every attempt, your computer may become infected with a virus or some malicious program. The virus must be removed in order to get your computer to its prior working state. Depending on the virus or program, the removal process can be simple or amazingly hard. Many viruses can be removed with common anti-virus software, while others must be manually removed. Often a removal program can be downloaded from the internet to remove the infection


•Step 1
Run your virus scanner to find the virus .In many cases, allowing the scanner to remove the virus is all you need to repair the damage. If this doesn't completely remove it, there are many other steps you can take to remove and repair virus damage.

•Step 2
Run your virus protection software in safe mode. By running the program in safe mode, all nonessential programs are disabled, meaning that only the programs needed to start Windows will load.

a) Turn on your computer. If your computer is on, restart it. If it is not on, press the power button.

b) Enter safe mode. When your computer restarts or powers on, repeatedly press the F8 key. The Windows Advanced Options Menu will come up. Use the arrow keys to select "Safe Mode" and press "Enter".

c) Choose your version of Windows. On the next screen, if there is more than one operating system on your computer, chose the version that you currently use.

d) Select the user that you are going to log under (if applicable).

e) Run a virus scan. When your computer has finished loading, start your virus program and allow the process to completely scan your computer.

f) Delete all detected viruses. Follow the process recommended by your virus scanner to remove all viruses.

g) Close your antivirus program.

h) Restart your computer.

•Step 3
Search the Internet. Your virus-protection program should have located the virus and supplied you with the name and type of infection that is on your computer. In almost every instance, the Internet can be a great reference for information about and the removal process of the virus. Often a free program exists that you can download to remove the virus. If the virus has hijacked your computer, you may have to use another computer to search for this information.

•Step 4
Run a system restore.After you have completely removed the infection, you may be worried that you have lost files from its attack. By running a system restore, you can restore your computer to a previous time.

a) Log on to Windows as an administrator.

b) Click "Start", point to your mouse to "All Programs," point to "Accessories," point to "System Tools," and then click "System Restore." System Restore will start.

c) Click "Restore my computer to an earlier time" on the next page (if it is not already selected), and then click "Next".

d) Choose the most recent system-restore point in the list, and then click "Next".

e) Click "OK" to confirm the list of configuration changes that System Restore will make.

f) Click "Next" on the Confirm Restore Point Selection page. System Restore restores the previous Windows configuration and then restarts the computer.

g) Log on to Windows as an administrator.

h) Click "OK."

•Step 5
Format your hard drive if running these processes did not remove the virus or the damage from the virus is too severe. By formatting your hard drive, you will erase everything that is currently on it and install a fresh version of your operating system. Use this only as a last resort. Before you proceed with this step, Microsoft suggests that you contact them for support. Check the Resources to link to more information

How to Fix Tires Without Removing Them

A flat tire on your vehicle is a major inconvenience. But you don't need a professional to fix it. Keep a tire repair kit in your trunk or glove box. In fact, you don't even have to remove the tire to repair


•Step 1
Use a car jack to lift the corner of the car with the bad tire.

•Step 2
Find the object that punctured the tire. If it's not immediately visible, spray the tire with soapy water, if handy. It will bubble around the leak.

•Step 3
Remove the object from the tire with pliers.

•Step 4
Clean out the hole with the rasp tool from the repair kit. Insert it into the hole and rock it back and forth (this both cleans the hole and roughs up the rubber so the patch adheres better).

•Step 5
Thread the plug through the needle tool from the repair kit. If necessary, coat the plug with the adhesive that's in the repair kit.

•Step 6
Insert the needle with the plug into the puncture, then remove it just enough so you can cut the plug from the needle. The hole should now be plugged.

•Step 7
Allow any adhesives used to dry.

•Step 8
Trim the plug flush with the tire.

•Step 9
Fill the tire using the aerosol tire filler or air pump.

•Step 10
Release the car jack to return the tire to the ground

How to Fix Power Washers

Power washers are a must-have for any homeowner. A high-pressure stream of water makes it easy to maintain patios, decks and walkways, and can even be used to clean aluminum or plastic siding on homes. But if the pressure drops or a strange noise develops, doing a relatively easy chore could become difficult or nearly impossible. Taking your power washer to get fixed could dip into your wallet unnecessarily. To diagnose and repair the problem, first make sure to consult your product manual. If all else fails, take your newly found knowledge and price compare parts at your local hardware store. Then, take your power washer to a professional and make sure you aren't being overcharged


•Step 1
If the pump runs but no flow is produced, this could indicate that the pump needs to be primed. To fix, flood the suction (usually a button you can press) and then restart the pump.

•Step 2
If you have a noisy pump, this could mean that the pump is sucking in air. To fix, check the suction manifold. If air has been trapped inside the pump, you must flood the suction hose and restart. Run the pump until the air has been evacuated. You will need to disconnect the discharge hose from the pump beforehand.

•Step 3
If you hear a loud knocking noise in the pump, chances are that a bearing is worn or broken, or there may be a pulley loose in the crankshaft. To fix, you may need to replace the bearing. Check the crankshaft and tighten any loose screws.

Checking the Pressure

•Step 1
If the pressure gauge is fluctuating and you can't explain why, the valves may be worn or blocked by foreign matter. If the problem hasn't been fixed after cleaning the valves, get them replaced.

•Step 2
Low pressure has many possible causes. Worn nozzles should be replaced (with the proper size). Belts can slip. Make sure all belts are tightened or replaced (with the proper size). During assembly the inlet plumbing may have not been sealed correctly. To fix, disassemble and reseal it.

•Step 3
Make sure the machine has the correct nozzle and that the nozzle isn't worn. A worn or incorrect nozzle can result in low pressure. If correct, the nozzle will match the pressure and flow of the pump. See your product manual for this information.

Fixing and Preventing Leaks
•Step 1
If the packing is worn, this may result in water leakage from either under the manifold or elsewhere. To fix, install new packing. Likewise, worn seals can result in an oil leak between the crankcase and pumping section. If the crankcase piston rod seals are worn, replace them.

•Step 2
If oil is leaking in the crankshaft area, check the bearing, the crankshaft seal and oil seal o-ring. If the bearing is bad, replace it. If the crankshaft or o-ring are worn, remove the oil seal retainer and replace all damaged parts.

•Step 3
Water in the crankcase may not be caused by a leak, but could be the result of collected condensation from humid air. To fix, change the oil intervals. It's recommended to use a high grade 30 weight (non-detergent) automotive oil.


Want agreat job ... click here

Have agreat live and enjoy it .. just click here

How to Repair Sagging Upholstery

Step 1
Turn the sofa or chair upside down, and use the staple/tack puller to remove the cloth bottom cover. This will give you a clear view of the underside of the springs. Locate the broken spring or springs.

Step 2
Using the staple/tack puller, remove the tacks holding the zigzag spring clips on both ends of the damaged spring. The spring will lift out when the clips are gone.

Step 3
Fasten one end of the zigzag spring in the clip, making sure the clip wraps around the length of the flat end of the zigzag. One edge of the clip will have tack holes and the other will have a partially open coiled edge to hold the spring. Using the pliers, pinch the coiled edge of the clip to hold the spring tightly. Do not hook the clip on the curved edges of the zigzag spring because it will not hold very long. Place a clip on each end of the spring.

Step 4
Position one clip, either one, over the holes where the original clip was located in the furniture's frame. Insert a tack in each hole, and tap it with the tack hammer until it is halfway in. Make sure the clip is straight, and use the tack hammer to gently pound the tacks in the rest of the way.

Step 5
Push the other end of the zigzag spring into the frame of the furniture. The spring should curve away from your hands and toward the cushion. Position the second clip over the original holes on the opposite side of the frame, and use the tack hammer to pound in the tacks.

Step 6
Position a piece of upholstery twine six inches from each end of the zigzag spring, where it attaches to the frame. Slide the twine ends under the closest spring and tie the twine pieces tightly, because it will keep the springs from sliding apart.

Step 7
Replace the cloth bottom cover and tack it back in place with tacks and the tack hammer. Turn the furniture back over.

Search for ajob .... click here and get it
Want to have agreat life ... visit this site and enjoy your life

Removing Scratches from your Car

Hey, we are talking about scratches in this segment and when you are dealing with a scratch on a vehicle there is a couple of ways to address it. If it is very light and superficial, you can sometimes remove the entire scratch by hand with a moderately aggressive compound. Most of the time, I address scratches with the same orbital that I used to apply wax. This particular machine is a professional machine that has a variety of speeds. On the maximum speed setting it is rotating at about 3000 rpm and with a proper pad and compound combination, I can remove some serious scratches without harming the paint. You can also use a buffer, but a buffer requires a lot of skill and a great deal of care because you can actually burn through the paint. I always use a dedicated pad for each product; don’t mix products on the pad, so with this example I am using a pad that is just for this moderate compound that I am using. Apply the compound to the scratch and again this is on its very highest speed. So start the process with the pad flat on the surface and don’t put too much pressure on the edge immediately. You are going to use that technique to actually get the scratch out but you need to have the orbital running before you tilt it up. Never let the surface of the pad just dwell in one area, keep it moving constantly. Even though this is spinning at a relatively slow speed compared to a buffer, you can still make a mark on the paint if you just let the pad rest on the area that you are working on without moving it back and forth. After you have removed the majority of the scratch with the compound, I usually use a three or four step method to ensure that the result is of high quality and after a compound I almost always use a slow remover, which is basically just a lighter compound, very little grip, very little abrasion and again we remove the pad that we have used with a compound and we apply another new pad that we are going to use with this slow remover. Basically the same technique is used; we go ahead and apply the product and again we want to start with a pad flat. When you are using the second step with the slow remover, it is not necessary to tilt the pad. Go ahead and just apply wax and again we are using the same orbital but we have turned it down to a more moderate speed and there you have it, the scratch is gone."

Watch this video

Do-it-yourself house-cleaning products

Say goodbye for these things

Spit and Vinegar - the rebirth of Do It Yourself healthy cleaning products!

Okay, maybe not spit. However, did you know that commercial house-cleaning products can be harmful to your health and the environment. Surprising to most, many of the chemical ingredients in household cleaners have never been tested for toxicity and disease causing properties in humans. Every year, thousands of untested chemicals enter the North American market - many of them used by you, or your children in everyday house cleaning.

Environmental products are readily available but can be overly expensive. Did you know many non-toxic and inexpensive common household products can be used to clean your home? In my mother's day, baking soda and vinegar could be used to clean almost everything. Surprise! They work just as well today. Below find a list of handy do-it-yourself cleaning products!

BAKING SODA:

Baking soda is not only safe to clean with, it is safe to eat! Baking soda can be used for cleaning in several ways:

* Use alone with some water on a sponge to clean any surface you'd clean with a powdered abrasive.
* Pour a cup of baking soda down the drain with a 1/2 cup of hot water and let it stand over night to remove clogs from drains. In the morning, follow with a pot of hot water from the kettle!
* Add cornstarch to baking soda and repeat the above process for especially blocked drains.
* Open a box of baking soda in the fridge, freezer, laundry room, recycling area - the baking soda will absorb unpleasant odors from the air - without releasing harmful chemicals other air fresheners cover up smells with.
* For pet stains and other unpleasant smells or stains, mix some baking soda with water, smooth over surface and allow to sit. After a few hours (or overnight depending on the stain or smell)vacuum or wipe up the baking soda with water, and allow area to dry.
* Leave a mixture of water and baking soda in pots or pans over night to remove tough baked on grime.
* Add vinegar or lemon juice to soda (don't be frightened by the fizzing!) to make a tougher scum busting formula for bathtub rings.
* Add baking soda during your clothes washing cycle to brighten whites without bleach!

WHITE VINEGAR - not just for salads:

Another safe to eat cleaning product, purchased for pennies in bulk!

* Dilute vinegar with an equal part of water to clean all surfaces and floors. You can use this safe mixture to clean anything you'd normally clean with a multi-purpose chemical surface cleaner.
* Use undiluted vinegar
Get a Widget for this title Do-it-yourself house-cleaning products
Top ArticleAll 18 Articles1
of 18 Write now Article Tools Page 2 of 2
to fight harder to clean stains or soap scum.
* Be careful when using vinegar on finished wood surfaces or marble as it may dull the surface.
* Pour vinegar into your toilet bowl, allow to sit, and then use a toilet cleaning brush to remove stains and bacteria from your toilet!
* Add vinegar to laundry during the rinse cycle as a fabric softener.
* Vinegar is a disinfectant, no need to use bleach on your food and bathroom surfaces!

LEMON JUICE:

* Use lemon juice to clean hard water stains, rust stains or soap build up. It is also a great grease cutter.
* Add lemon juice to baking soda for a get dish cleaning solution!
* Mix lemon juice with olive oil and use in place of furniture polish!

SALT:

* Salt may be bad for your blood pressure when eaten, but it is the best red wine remover in the world! Simply pour salt over the spill, rub it in and let stand. Repeat as necessary until the salt absorbs the whole stain. Vacuum up extra salt.

* Aside from red wine, salt makes an excellent scrub and stain remover.

* Mix salt with olive oil as an excellent skin exfoliant (stretching here, but you clean your face IN your house!).

* Salt mixed with lime juice will remove rust stains, and sometimes blood stains!

CLUB SODA:

* Use in place of a stain removing spray on fabric stains. Allow soda to soak before blotting the stain. Do not rub the stain lest you spread it.

* Put club soda into a spray bottle and use in place of glass cleaner.

OLIVE OIL

* Olive oil (especially when mixed with lemon juice) makes an excellent furniture polish. Fortunately, the cheaper olive oil works just as well as expensive brands!

* Olive oil is an excellent hair conditioner!

CORNSTARCH:

* Use cornstarch in place of carpet cleaning and deodorizing powder.

* It can also be used as a window cleaner and furniture polisher, but other methods are less messy. It will do in a pinch though. Be sure to wipe off thoroughly so you don't have streaks!

HOT WATER:

* Boiling hot water is a sterilizing agent. Pour over dishes after washing before drying!

* Boiling water is a GREAT pest killer. Pour over dandelions, other weeds and even ant hills instead of using harmful herbicides and pesticides.

BEER:

* Beer mixed with water in a bowl is great for catching and killing earwigs. A great substitute for using spray pesticides in your house. Chemical pesticides are harmful to your family!

BORAX:

This is not a safe to eat product. Borax is a brand name for sodium borate. I'm only adding it to my list because it makes an excellent bug killer, and is less harmful to humans and the environment than commercial pesticides. Put a ring of borax around your house to ward off ants - removing the need for pesticides inside your house!

I DO NOT RECOMMEND:

BLEACH: Most of the things you use bleach for you can substitute in less harmful products listed above. Bleach is often used to "kill" mold and mildew. It does not do so. At best it bleaches mold so you can no longer see it until it regrows. At worse mixes with certain molds to cause a toxic airborne by-product.

watch this ...